12 Volt Switched Mode Power Supply (PSU) for CCTV, HDD, Wifi AP | 60 Watt or 90 Watt or 120 Watt

12 Volt Switched Mode Power Supply (PSU) for CCTV, HDD, Wifi AP | 60 Watt or 90 Watt or 120 Watt

You can use it on any 12 Volt Device e.g Router, Wifi Access Point and CCTV Cameras, 5 Amps is enough to provide constant 50watt to all devices and will power 3-4 cameras from one power supply.

12 Volt/60 Watt Max Usage Switched Mode Power Supply Specifications – No Power cord included 

INPUT

• Input range : 85 ~ 264 VAC
• Input frequency : 47 ~ 63 Hz
• Inrush current : 15A at 115VAC; 30A at 230VAC; cold start at 25
• Input current : 1.5A Max
• Leakage current : 0.5 mA at 50/60 Hz 264VAC input

OUTPUT Rated output power : 60 Watts Max (50 Watts or less recommended to prevent device 80%+ power usage and overheating)

• DC Connector : 5.5mm OD & 2.1mm ID (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
• Output voltage : 12V± 4%
• Output current : 5A
• OL protection 96% to 104% above peak rating
• Ripple & noise 200mV at rated load

• Operating temp : 0 to 50 ambient derate each output at 4.0% per degree from 50 to 60
• Storage temp. – 40 to 85
• Operating humidity 5% to 95% (non-condensing)
• MTBF 100,000 hours at full load and 25 ambient conditions (demonstrated)

12 Volt/90 Watt Max Usage Switched Mode Power Supply Specifications – No Power cord included 

INPUT

• Input range : 85 ~ 264 VAC
• Input frequency : 47 ~ 63 Hz
• Inrush current : 15A at 115VAC; 30A at 230VAC; cold start at 25
• Input current : 1.5A Max
• Leakage current : 0.5 mA at 50/60 Hz 264VAC input

OUTPUT

• Rated output power : 90 Watts Max (70 Watts or less recommended to prevent device 80%+ power usage and overheating)
• DC Connector : 5.5mm OD & 2.1mm ID (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
• Output voltage : 12V± 4%
• Output current : 7.5A
• OL protection 96% to 104% above peak rating
• Ripple & noise 200mV at rated load

ENVIRONMENTAL

• Operating temp : 0 to 50 ambient derate each output at 4.0% per degree from 50 to 60
• Storage temp. – 40 to 85
• Operating humidity 5% to 95% (non-condensing)
• MTBF 100,000 hours at full load and 25 ambient conditions (demonstrated)

12 Volt/120 Watt Max Usage Switched Mode Power Supply Specifications – No Power cord included 

INPUT

• Input range : 100 ~ 264 VAC
• Input frequency : 50 ~ 60 Hz
• Inrush current : 100~240Vac 50/60Hz max: 90~264Vac 47/63Hz

OUTPUT Rated output power : 120 Watts Max

• DC Connector : 5.5mm x 2.5mm, compatible with 5.5mm x 2.1mm (Check DC Input size same on device but most 12 Volt devices uses this diameter on DC Power connector)
• Output voltage : 12V± 5%
• Output current : 10A
• OL protection 115% to 135% above peak rating
• Operating temp : 0 to 50ºC ambient derate each output at 4.0% per degree from 50 to 60
• Storage temp. – 40 to 80ºC
• Operating humidity 20% to 90% (non-condensing)

Note!!! Please do not buy a power supply rated for less watts than being used. Adding multiple strings of LED lights to a power supply or more cameras / hard drives that uses more than 80% of the rated output of the power supply, will cause overheating to the power supply and damage / cut-off. Make sure you calculate max watts on connected devices to be less than 80% of power supply max amps/watts rating.

Power Cord that works with the power adapter

1.8 Meter Dedicated Red Plug PC Power Cable | 3 Pin Electrical Plug to Kettle Cord | IEC Plug (C13 Plug)