Single mode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Specifications:

• Indoor Cabling Bow-Type Drop Cable
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Duplex (Dual Fiber Cables and DUAL LC Connectors on each side of cable)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode Dual LC 1.25Gbit 1310nm Gigabit SFP Transceiver Module | Cisco, Huawei, Dell Compatible

10Gbps Fiber SFP+ Module | Single Mode Dual LC Transceiver | 10km | Cisco, Huawei or Generic Switch Compatible

Single Mode Fiber Cable Usage and Instructional Video

Single mode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Specifications:

• Indoor Cabling Bow-Type Drop Cable
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Duplex (Dual Fiber Cables and DUAL LC Connectors on each side of cable)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode Dual LC 1.25Gbit 1310nm Gigabit SFP Transceiver Module | Cisco, Huawei, Dell Compatible

10Gbps Fiber SFP+ Module | Single Mode Dual LC Transceiver | 10km | Cisco, Huawei or Generic Switch Compatible

Single Mode Fiber Cable Usage and Instructional Video

Singlemode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Please see our guide at Fiber Optic Cables & SFP Compatibility for more information.

Specifications:

• Indoor or Outdoor Installation
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Simplex (Single Fiber Cable and LC Connector Single Head on each side)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode BiDi SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX Bi-Directional

3km Single Mode Bi-Directional SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX BiDi SFP

The POE Network Switches and Gigabit Network Switches below are installed with this cable and Fiber SFP’s

26 Port Rack Mountable Gigabit Network Switch | 2 SFP Ports for Transceiver Modules | OEM

18 Port Rack Mountable Gigabit Switch | 2 SFP Ports for Transceiver Modules | OEM

6 Port Gigabit POE Network Switch with SFP Port & RJ45 Uplink Port

400 Watt Rack Mountable 28 Port Gigabit POE+ Network Switch with 2 SFP Transceiver Module Ports | OEM

LC Fiber Connectors Explained in Detail

Single Mode Fiber Cable Usage and Instructional Video

Singlemode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Please see our guide at Fiber Optic Cables & SFP Compatibility for more information.

Specifications:

• Indoor or Outdoor Installation
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Simplex (Single Fiber Cable and LC Connector Single Head on each side)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode BiDi SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX Bi-Directional

3km Single Mode Bi-Directional SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX BiDi SFP

The POE Network Switches and Gigabit Network Switches below are installed with this SFP

26 Port Rack Mountable Gigabit Network Switch | 2 SFP Ports for Transceiver Modules | OEM

18 Port Rack Mountable Gigabit Switch | 2 SFP Ports for Transceiver Modules | OEM

400 Watt Rack Mountable 28 Port Gigabit POE+ Network Switch with 2 SFP Transceiver Module Ports | OEM

LC Fiber Connectors Explained in Detail

Single Mode Fiber Cable Usage and Instructional Video

Singlemode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Specifications:

• Indoor or Outdoor Installation
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Simplex (Single Fiber Cable and LC Connector Single Head on each side)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode BiDi SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX Bi-Directional

3km Single Mode Bi-Directional SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX BiDi SFP

The POE Network Switches and Gigabit Network Switches below are installed with this SFP

26 Port Rack Mountable Gigabit Network Switch | 2 SFP Ports for Transceiver Modules | OEM

6 Port Gigabit POE Network Switch with SFP Port & RJ45 Uplink Port

400 Watt Rack Mountable 28 Port Gigabit POE+ Network Switch with 2 SFP Transceiver Module Ports | OEM

18 Port Rack Mountable Gigabit Switch | 2 SFP Ports for Transceiver Modules | OEM

LC Fiber Connectors Explained in Detail

Single Mode Fiber Cable Usage and Instructional Video

Singlemode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Specifications:

• Indoor or Outdoor Installation
• Diameter  : 3mm
• Duplex (Dual Fiber Cables and DUAL LC Connectors on each side of cable)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• Cable is marked with “A” & “B”

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

Add link to Bidi SFP and Other SFP’s For Simplex Cable

LC Fiber Connectors Explained in Detail

Single Mode Fiber Cable Usage and Instructional Video

Singlemode fiber optic patch cables come with a 9 micron diameter glass core. With the cladding layer, they are 125 micron, and with the buffer layer they are 250 micron. To prevent excessive loss (attenuation), you should ensure that you only connect single mode cables to other single mode fibers already in your system.

Specifications:

• Indoor or Outdoor Installation
• Diameter  : 3mm
• 2*0.45mm steel strength member
• Simplex (Single Fiber Cable and LC Connector Single Head on each side)
• LC/UPC LC/UPC
• G.657A2, 2.0×3.0mmmm
• LSZH (Low Smoke, Zero Halogen)
• UV resistant

Tensile Strength

Always take care when installing fiber cables to ensure not to break the fiber inside the cable by over-bending or twisting cables. These cables strengthened by the 2*0.45mm steel wires provide more than enough pulling strength to easily install these cables in difficult environments without breaking the cable.

G.657A2 Bend Ratio vs Other Specifications

These Fiber Cables Are Commonly used with the Fiber SFP’s below

20km Single Mode BiDi SFP Transceiver Module SET | Cisco Huawei Dell Compatible | 1000BaseBX Bi-Directional

The POE Network Switches and Gigabit Network Switches below are installed with this SFP

26 Port Rack Mountable Gigabit Network Switch | 2 SFP Ports for Transceiver Modules | OEM

LC Fiber Connectors Explained in Detail

Single Mode Fiber Cable Usage and Instructional Video

High Quality and Cost-Effective 9/125μm Single Mode Bend Insensitive Fiber Optic Cable

The 9/125μm single mode bend insensitive fiber optic cable has less attenuation when bent or twisted compared with traditional optical fiber cables and this will make the installation and maintenance of the fiber optic cables more efficient. It can also save more space for your high density cabling in data centers, enterprise networks, telecom room, server farms, cloud storage networks, and any places fiber patch cables are needed.

How to Make a Fiber Optic Cable (SC to SC Cable ) Instructional Video

This 9/125um (Micron) single mode fiber optic cable is ideal for connecting 1G/10G/40G/100G Ethernet connections, HDMI over Fiber Optic Extenders or from your Fiber Router for Fiber to the Home (FTTH).

It can transport data for up to 10km at 1310nm, or up to 40km at 1550nm.

Fiber Optical Connectors for SC Ports below

Fiber Optic SC Connector – Field Installation for 125 Micron Fiber Optic FFTH (Fiber-to-the-home)

LC UPC Fiber Optic Fast Connector | Field Terminated Connector

Fiber cables can be extended by using a coupler as below

Simplex Single Mode SC APC to SC APC Fiber Optic Cable Joiner | Fiber SC Coupler

Duplex Fiber Optical Coupler | Female-Female LC UPC Single Mode Fiber Cable Joiner

The Tools below are commonly used with this fiber cable

12-in-1 Professional Fiber Optic Tool Kit incl Precision Fiber Cleaver, Fiber Strippers, Fiber Tester

Fiber Optic Cable Stripping Tool | Strip 125 micron fiber optical cables

Fiber Cable Stripping Tool for 125 micron fiber for FTTP or FTTH Applications

Fiber Visual Fault Locator Pen 10mW (Fiber Optical Light Pen) – Fiber Fault Trace Tool

Fiber Optic Cable Tester / Light Meter Tester with Display Screen – Can Test FC,ST and SC Cables